Rating of the best angle nozzles for screwdrivers and drills for 2022

A screwdriver and a drill are those universal tools that every self-respecting craftsman should have in his working set. For the first, the main purpose is to screw in fasteners, and for the second, to drill holes. It is worth noting that both of these devices can in some cases completely replace each other: a striking example here is the fact that both a drill and a screwdriver can be used to stir sticky building materials. And to increase their functionality, it is possible to install all kinds of adapters on them, which include corner nozzles.

Corner adapter - general information

It is designed for drilling holes / screwing in fasteners in places where it is impossible to position the working device at a usual expanded angle, in other words, in confined spaces. The body of this nozzle is characterized by the presence of elements placed at an angle of 90 degrees. At the same time, only the drive spindle is located inside the adapter, together with the working part holding the drill / bit.

Directly on the body there is a part for installing the adapter at a right angle, in which the swivel bushings are located one inside the other. They are installed inside the case. This position ensures proper rotation and does not produce excessive noise.

In order to perform special types of work, for example, for driving screws into a soft base, it is also possible to use a hand tool, such as an angle screwdriver.

Modern types of corner fixtures

In total, there are two types of nozzles under consideration:

1. Flexible - in it the direction of the torque changes along a flexible connection.Outwardly, such an adapter looks like a Soviet-era dental tool - a drill, which, in fact, is a flexible shaft. At one end, the shaft is connected to the socket of a screwdriver / drill, and a bit is put on the other. In terms of its ability to work in confined spaces and hard-to-reach places, such a model is significantly superior to its “hard” counterpart. It is able to remove tight-fitting screws or drill holes in medium-weight material, which is not always possible with a rigid chuck. In most cases, flexible samples are used in the household, due to the low torque. The flexible chuck does a very poor job of driving screws into metal bases.
2. Rigid - in this shortened nozzle, the direction of the torque changes due to mechanical links. Her cartridge has greater strength than the flexible variation. So, with rigid models it is convenient to unscrew/twist hardware located to the right and left of the force application axis, as well as drilling holes in these directions. Rigid adapters are used for installation on professional grade equipment. The mechanical method of force transfer allows you to get an output torque with an indicator of 40 to 50 Newtons per meter. Rigid models are often equipped with a special set of nozzles that soften vibrations and stress, which can occur when working on metal bases.

IMPORTANT! When working with the angle nozzle, do not apply excessive force to it - this will create an increased load on its inner shaft, which will increase the risk of nozzle failure!

Main technical parameters, functionality, advantages and disadvantages

Corner adapters are able to work on a flexible axis change or on its mechanical transfer. The latter variety is mostly used on professional drills. It should be noted that a professional drill must have a maximum speed of at least 1800 rpm. Such a high-speed mode will allow you to achieve the proper torque to carry out difficult drilling operations. The flexible type of adapters is mostly suitable for screwdrivers, because it works due to the flexible shaft, and it is convenient to fix the device itself with one end directly on the tool, and install a bit or drill in the second.

Angular gearboxes may differ in significant technical parameters and have their own design features:

• Production material - regardless of whether an adapter has been produced for a screwdriver or a drill, it is made of a material that can withstand increased mechanical loads. As a rule, such material is high quality metal, which will perfectly cope with screwing / unscrewing fasteners and drilling holes in solid bases.
• Features of changing the axis - the adapter, in fact, is a gearbox enclosed in a rugged case. By changing the working axis, the device will reduce the load on the operator's hands, while the torque itself in the device will not be excessive.
• The extension size of the bit is the distance that the working part can be extended.
• Rotary angle - the convenience of controlling the tool as a whole will depend on this parameter, for example, the ability to work with it with two hands.
• The presence of a reversible function - with the help of this function it is possible not only to screw in the screws, but also to unscrew them.

Corner adapters have a number of significant advantages:

• Easy to put on and take off;
• Very easy to manage;
• The material is processed evenly, no burrs remain on the bases;
• In most cases, they are multifunctional;
• Able to show high efficiency;
• Unpretentious in service.

The disadvantages include:

• Some models from well-known brands are very expensive;
• Models for screwdrivers and drills for some situations may not be completely interchangeable;
• Home versions in terms of functionality are significantly inferior to professional samples;
• Not very suitable for polishing dense materials at a 90 degree angle.

Design features of flexible and rigid models

In terms of their components, flexible and rigid corner adapters differ significantly from each other. So, flexible options consist of:

• Housing made on the basis of plastic corrugation or metal;
• The capture of bits is carried out by means of a magnet;
• There is a flexible shaft;
• The adapter is attached to the main chuck of the screwdriver.

Rigid models include in their design:

• Housing made of aluminum alloy or durable steel;
• Reducer;
• Handle for gripping the tool with both hands (the handle can be rotary or fixed);
• The gripper for a bit can be simple magnetic (less reliable) or be made in the form of a three-jaw chuck of particular complexity and increased reliability;
• There is a bearing responsible for the rotation of the main shaft.

IMPORTANT! It is not recommended to use excessive muscular force when working with rigid type elbow adapters, as this may disturb normal working conditions and lead to rapid bearing wear.Moreover, it is always necessary to take into account the power of the drill itself (screwdriver), because when using nozzles on it, this indicator will decrease. Thus, at full speed it is possible to use the device with an adapter only for a short period of time. Otherwise, the risk of motor overheating will obviously increase due to its overload.

Difficulties of choice

Considering that the devices in question are add-ons for the main equipment, it is better to purchase an adapter made by the same brand for each tool. Although there are universal adapters on the market, professionals advise once again not to expose your screwdriver or drill to unnecessary risk of working with third-party components. Thus, when buying a nozzle, you should pay attention to the following points:

• The adapter must confidently withstand at least 300 rpm;
• The presence of a magnet to capture the bit is required;
• The shank and chuck must be adapted to a minimum bit size of 6 millimeters;
• The chosen adapter brand should have a good reputation (and preferably be the manufacturer of the main tool);
• The accompanying documents (instructions) must accurately and fully describe all technical parameters;
• It is desirable to have a quality certificate confirmed by Russian certifying organizations;
• It is desirable to have various options for fixing the bit / drill;
• Ability to adjust the height;
• Adjustable screwing or drilling depth.

IMPORTANT! If the angle adapter is selected specifically for the drill, then the possibility of fixing it with the help of transitional magnetic rings will be important, which will greatly facilitate fixation in the chuck.This feature will help to securely fix the bit, and it will be possible to remove it only by pressing the adapter protrusion.

Technical aspects of the choice of nozzles for a screwdriver

To begin with, it is necessary to clearly define consumer requests, that is, what screwing depth will be required, what the minimum height will be needed, what will be the range of fastener diameters. To determine the last parameter, it is possible to use the following ratios (data are oriented to work on medium-density metal bases):

1. With the largest fastener diameter of 8 millimeters, the torque must be at least 12 Newtons per meter;
2. With the largest fastener diameter of 12 millimeters, the torque must be at least 20 Newtons per meter;
3. With the largest fastener diameter of 16 millimeters, the torque must be at least 30 Newtons per meter;
4. With the largest fastener diameter of 21 millimeters, the torque must be at least 60 Newtons per meter;
5. With the largest fastener diameter of 50 millimeters, the torque must be at least 180 Newtons per meter.

Also, you need to pay close attention to the way the bit is attached to the nozzle. As a rule, brands known for their quality supply the adapter for these purposes with special magnetic rings installed in the screwdriver chuck. This makes reliable fixation of non-magnetized bits and heads of the self-tapping screws themselves. The extraction of the ring is carried out by pressing the cross-shaped protrusion located on the adapter body. However, it is better to check the quality of fixation immediately on site before purchasing the product.The thing is that sometimes, the fastening may not be too reliable due to the small size of the ring, which is the “payment” for the overall compactness of the adapter.

Features of work with corner adapters

Naturally, when working with the use of angle nozzles, it is necessary to follow the safety regulations. In addition, it is advisable to apply the following practical tips during work:

• The bit or drill must be securely fixed in the adapter, as well as the adapter itself must be securely fixed in the main tool;
• If the adapter is mounted on a drill, then it is preferable to hold it with both hands;
• Regardless of the device used for corner work (drill or screwdriver), do not put excessive pressure on it;
• It is forbidden to change the operating mode until the rotation of the device completely stops;
• The operator must use personal protective equipment during work;
• Immediately after completion of work, it is forbidden to touch the nozzle, because it will be extremely hot.

Rating of the best angle nozzles for screwdrivers and drills for 2022

Budget segment

3rd place: "Angle adapter with hex shank for drill TUNDRA 4622485"

A very simple and extremely cheap option for a drill. Can only be used with one type of 0.25" hex holder. The case is made of soft aluminum alloy, which raises some questions about the durability of the work. At the same time, it is easy to install and is quite capable of handling drilling in materials that are not too hard. Designed for household models of drills. The country of origin is Russia, the established cost for retail chains is 375 rubles.

• budget cost;
• Magnetic fastening bits;
• Focused on household drills.

• Not a very strong body.

2nd place: "AV Steel AV-805140"

The internal elements of this device are made of metal by pressing them. The case is monolithic and cannot be dismantled. Inside there are several interconnected gears made of aluminum. The adapter is adapted for short and shallow work with small self-tapping screws, by screwing / unscrewing them from softwoods. The country of manufacture is China, the recommended cost for retail chains is 540 rubles.

• Monolithic body;
• Light weight;
• Sufficient length.

• Not fit for long hours

1st place: "KWB 1181-00"

This nozzle is designed for a torque of 14 Newtons per meter. The body and nuts for the gear screed are made using casting technology. The magnetic function is implemented at an average level, due to the use of silumin. The driven and driving gears are made of high quality steel, the rest are hardened. Although the manufacturer did not bother to lubricate the internal elements, it is not a problem to lubricate them. The country of origin is Taiwan, the recommended retail price is 990 rubles.

• The driving and driven gears are made of high quality steel;
• budget cost;
• Casting technology.

• No initial internal lubrication.

Middle price segment

3rd place: "Bosch 1.600.A00.1Y8"

This model is a type of accessory for Bosch cordless screwdrivers of the I-X-O series, which means that they can only be used with tools from this line. It is used for screwing screws in hard-to-reach places. The length of the nozzle is 5.5 centimeters, and the material of manufacture is durable carbon fiber. The country of origin is Germany, the recommended cost for retail chains is 1300 rubles.

• Rugged housing;
• Quality of execution;
• Adequate cost.

• Some massiveness of the case does not allow using the adapter in very narrow places.

2nd place: "AEG 4932430173"

Just the perfect corner fixture from a world famous brand. Can be used not only with nutrunners and screwdrivers, but also suitable for drills. Designed to work with torque up to 14 Newtons per meter. Perfectly twists and unscrews screws in very hard to reach places. The body and internal gears are made of specially hardened steel. The magnetic holder has six faces and is designed for a size of 0.25 inches. There is a 360-degree swivel finger stop lever. The country of origin is Germany. The established cost for retail stores is 1600 rubles.

• Includes 10 magnetized screwdriver bits;
• Robust housing and gears;
• Hex holder.

• Not detected.

1st place: "Quick for Powermaxx BS Quick Metabo 627261000"

This angled tool is designed to work in hard-to-reach places. Mounts on Metabo PowerMaxx BS Quick and Metabo BS 18 Quick tools. Magnetic bit holder for 0.25 inch hex bits.It can work freely on both left and right sides. Designed for torque rates up to 28 Newtons per meter. The country of origin is Germany, the established cost for retail chains is 2,500 rubles.

• In fact, it is universal, because it is suitable not only for Metabo instruments;
• Freely spinning in all directions;
• It is possible to fix the desired angle.

• Not detected.

Premium class

3rd place: "BBS12C2-RAA AEG 4932430222"

A professional sample from a world famous brand that perfectly expands the capabilities of a profile tool. The attachment diligently and 100% maintains the same torque as the main tool thanks to a very good spindle grip. The body is made of heavy-duty metal. Fixation of the cartridge is possible on the nozzle, which makes it easy to perform drilling operations. The country of origin is Germany, the established cost for retail chains is 3,600 rubles.

• Reliable fixation - installed bits do not vibrate;
• Even under heavy loads, no backlash is observed;
• Accelerated installation on the shaft.

• Not detected.

2nd place: "QUICK Metabo 627242000"

This angular adapter is quick-detachable and works with the corresponding line of devices from the Metabo manufacturer. Due to the latest design, it may not fit tightly on very old models from its manufacturer. It has a system for quick change of fasteners without the use of native tools for removal. The holder is magnetic, for bits with a hex shank and a size of 0.25 inches. The adapter itself is suitable for both left and right rotation.Designed for use on cordless tools with torque up to 110 Newtons per meter. The country of origin is Germany, the recommended cost for retail chains is 3900 rubles.

• Can work with high torque;
• Has a quick fix system
• Adequate cost.

• May not be compatible with very old QUICK Metabo models.

1st place: "BSB 18CBL-RAA AEG 4932430924"

An expensive and very professional adapter that can work perfectly with all AEG profile tools. Capable of properly transmitting torque to the tooling from the main tool spindle without changing/lowering its speed. The body is made of durable metal, coated with an anti-corrosion compound. The device is able to rotate 360 ​​degrees and can work in very tight spaces. The country of origin is Germany, the recommended retail price is 6,700 rubles.

• Ability to work with any "native" profile tool;
• Rugged housing;
• 360 degree rotation.

• Very high price.

Conclusion

An angle adapter will help turn a screwdriver or drill into a versatile tool that can perform many different functions, especially coping with work in hard-to-reach places. However, to select a suitable adapter, you should always initially determine the future tasks and conditions of the intended work, as well as take into account its significant technical characteristics. It is always better to make the only right choice than to suffer for a long time with constant returns of goods.

It should be noted that the premium class of the tools in question is represented exclusively by products from abroad and their price is quite a lot, which is more than offset by the quality of workmanship and work. The Russian manufacturer occupies exclusively the lower price segment and the quality of its products leaves much to be desired.