Ranking of the best siding manufacturers in 2022

Siding is a building panel that is installed on the outside of a room and is attached to a metal or wood mesh, which ultimately makes it possible to give a beautiful look to all surfaces of the house. This design allows you to distribute insulating materials in the inside, as well as protect the side surfaces from various natural factors.

In order to choose the right finishing material, it is worthwhile to properly study the products of all possible siding manufacturers. It is in this article that there is a list of the best brands of siding materials. First of all, before choosing a particular company, it is necessary to study all the advantages and disadvantages, as well as the capabilities of each manufacturer. Comparing the parameters of all options, it becomes clear which manufacturer is better.

Siding Selection Criteria

At the moment, siding manufacturers produce a wide range of quality panels for residential applications. Before you get acquainted with the rating of the best manufacturers, it is worth determining the following criteria for evaluating siding.

• The number and quality of layers - first of all, you need to pay attention to this criterion. Resistance to deformations and other natural phenomena depends on the quality of the panel coating. If the panel consists of a single pigment layer, then its approximate service life will be several years. After that, the surface of the panel will begin to lose its resistance to precipitation and begin to collapse. For a long service life, a four-layer panel consisting of primed and varnished surfaces is suitable. However, such siding will have a high cost.
• Impact resistance level - when choosing a particular panel, it is worth considering its ability to mechanical deformation. Small and large stones, heavy rain, hail or accidental impacts - all this can leave a noticeable mark on the surface. There are models on which abrasions will remain, on others - cracks, on others - scratches.
• Fire resistance level - there are such representatives of siding that have in their composition substances that are not amenable to fire or intense heat, and there are those that, in contact with ignition, release poisonous gas into the air.
• Wind resistance level - there are special panels that can withstand strong gusts of wind. The level of wind resistance in such materials ranges from 150 to 300 km/h. Panels of this nature are suitable for residents who live in the steppe and mountainous areas.
• The nature of operation - there are several types of panels that are suitable for both interior and exterior decoration. Depending on the purpose, the materials contain the appropriate substances. For example, only environmentally friendly materials are used in internal surfaces.
• Appearance - in addition to the fact that the panels have a variety of colors, the arsenal of design solutions includes imitation of natural stone, natural wood, cinder block or brick.
• The composition of the model - when choosing panels, it is worth considering not only the total surface area. It is imperative to take into account all possible angles, frames, drops, ends and the height of the room itself. To help with the processing of all surfaces, there is a special kit in the form of a J-profile and connecting nodes that are necessary for installing panels
• Necessary certificates - when purchasing siding, it is necessary to check the availability of certificates, which should be in one set. This document must contain all the exact parameters of the panels, as well as a guarantee for uniform painting and operation.

Siding type

First of all, you should pay attention to the type of siding. Criteria, of course, help determine the best options, however, first of all, you need to decide on the type of panels.

Siding is divided into three types, and each of them has its own characteristics.

1. Vinyl siding - the advantages of these panels include the average price category, good moisture tolerance, ease of cleaning, resistance to low and high temperatures, the ability to melt rather than burn when in contact with fire, a huge range of colors, as well as the ease of the structure itself.The disadvantages include yellowing of light shades, deformation in sunlight, cracking from impacts, a relatively short service life, the ability to release toxic gas during combustion.
2. Acrylic siding - its advantages include a multilayer structure, increased resistance to ultraviolet rays, the ability to withstand deformation when heated up to 70 degrees, easy maintenance and installation of panels, as well as withstanding mechanical loads and environmental friendliness of the materials in the composition. The disadvantages of acrylic siding can only be attributed slightly overpriced.
3. Metal siding - these panels have the advantages of a fairly long service life, the widest choice of colors, resistance to fire and strong temperature changes. Such profiles have 3-4 layers of coating and parasites do not start in them. There are enough disadvantages in these panels, and they include too high a price, a decrease in thermal insulation, fading of colors after a long service life, deformation after impacts, the ability to rust in places where the paint has peeled off and a very difficult installation due to the large weight.

Having become acquainted with all the advantages and disadvantages of each type of panel, it becomes clear that these coatings are the best option of all types of sheathing. Moreover, siding has the best insulation and has a long service life.

List of the best siding companies

dock

The best manufacturer of siding is the German company Docke, which is able to produce the highest quality and at the same time inexpensive products. Despite this, the coatings of the German company are available for free purchase in many countries.In the Russian Federation, several branches were opened, in which, under the supervision of the founders, siding is being produced. Products in these factories are manufactured using German equipment and German materials.

The name of the company is a true reference to the word "cover" (translated from German), which subsequently clearly hints at the priority in the activities of manufacturers.

Among the reviews of reputable experts, you can find instructions regarding free access to all component parts of the siding. In case of a lack of any nodes, you can safely find a service company that contains all the necessary details.

Docke currently produces over nine million square meters of pavement per year and these products are divided into several classes. Taking into account the incomes of all segments of society and their opportunities, the company produces Lux, Premium and Standard series, which have unique, in relation to each other, distinctive features. In the most expensive series, there is mahogany drawing, in cheaper versions there are regular colors with various ornaments.

• A huge range, taking into account the cost and appearance;
• Service life: within 50 years;
• The Russian Federation has about 8,000 official siding stores.

• The ability to melt and emit poisonous gas;
• The vast majority of production comes from vinyl;
• Too high cost.

Vox

This manufacturer appeared in the early nineties of the last century in Poland and at the moment its products are widely represented in Europe, Africa and Asia. In addition to siding products, the Polish company is engaged in the production of not cheap furniture, and their choice of coatings is not very large.Most of their siding is made up of vinyl panels. The company's product range includes facade slabs with timber colors, plinth panels with imitation of brick and stone (this effect gives color to the foundation) and ship-type coatings with an overlap structure.

Also in the catalog there are soffit strips that can be used to process a visor or box.

Basically, buyers claim that the panels have increased fire resistance and density. This is evidenced by a small test, during which the panel lay in the fire for a long time before it melted.

Experts also note that Vox products are distinguished by a well-designed installation scheme, which carefully indicates all the nuances of panel installation. Also in this scheme there is the presence of all finishing materials, components and elements for processing walls. Such a move is very practical, because it can help even an amateur to ensure the installation of siding.

• Availability of refractory panels;
• Difference from similar panels due to the large section of the profile;
• Warranty and all necessary certificates;
• Availability of installation diagram.

• In the cold season, the panels begin to narrow;
• Peculiar smell after installation;
• Too little choice;
• Production of exclusively vinyl surfaces.

Alta Profile

This manufacturer is a prominent representative of high-quality, domestic siding. Alta-Profil began its production in 1995 in the Moscow region and has reached certain heights. Among Alta's products, you can find 3 types of interior decoration: Alta Siding, Acrylic and Prestige. The company's assortment includes brown and white fittings, and it is necessary for installing the planks.As for vinyl siding, it is available in several colors, namely lemon green, strawberry and beige. For lovers of sophisticated design, there is acrylic siding in purple and pistachio.

Product reviews are mostly positive. Ordinary builders claim that the installation of panels is very easy. This is facilitated by the rapid cutting of acrylic materials with a special tool, while there are no defects.

Experts, in turn, call Moscow products the best among cheap siding. Despite the low cost, the panels retain color saturation for a long time. According to the certificate, the service life can be about 50 years.

• The presence of acrylic siding with unusual shades;
• Low price category;
• Processed with a cutting tool without defects;
• Free use of panels with a profile section of 0.5 mm.

• Some models burn out within a few years;
• Weak resistance to mechanical stress;
• Limited color range of vinyl panels;
• Expensive accessories.

Mitten

A Canadian siding manufacturer that began its production a little over 50 years ago, but is already known around the globe and deserves praise from many experts. The products of this company are widely used in many countries of Europe and Asia. In Russia, panels from Canadians have been on sale since 1995 and have good reviews, even though only vinyl coatings are produced.

Among the products of the Canadian company there are two lines: Sentry and OregonPride.According to the instructions of the manufacturers, the installation of panels can be carried out even during severe frosts, however, this can lead to an undesirable effect in the warm season, so you should not tighten the bolts to the very limit. The fact is that after warming, the panel will begin to swell, and in the case of a strong pressing of the bolts, the surface will begin to crack.

Experts note vinyl panels from this manufacturer as one of the best because of their increased strength. Mitten siding has a profile section with a thickness of 1.2 mm and it perfectly resists various mechanical deformations. During cleaning, strong pressure can be applied, as the panels can withstand almost any force.

• Increased surface strength;
• Good wind resistance;
• Long durability of colors;
• Availability of certificates and guarantees.

• The possibility of swelling of the coating during solar heating in case of improper installation;
• Lack of metal and acrylic models;
• Too high price.

Tecos

This company produces high-quality products that have been known in Russia for 15 years. Tecos produces a wide variety of panels in terms of design, having an acrylic and vinyl composition.

Among the reviews, there are often comments from satisfied customers who note the elegance of a cylindrical beam with oak coloring. They also praise a range of slats that are painted in a natural stone style.

In the Russian Federation, first of all, the manufacturer has a good reputation due to the low cost of materials. However, this price has side effects in the form of poor quality of the pigment layers of the panel, which are guaranteed for several years.

Experts recommend taking light-colored panels and using them for houses that are surrounded by a lot of trees. In this way, finishing the house can last much longer than expected. Also, experts note the quality of control of sales of products by their manufacturer. It is because of this that they are considered among the best in the business. Tecos has developed a special website where the assortment of all materials is laid out at a real price, taking into account the costs of intermediaries. Thanks to this, the client can save on overpayments in stores.

• The presence of rare terracotta colorings for stone and brick;
• Availability of a special laboratory for quality control of materials;
• Manufacturing in Russia;
• All necessary certificates are included in each set.

• Grooves and spikes during assembly do not always coincide with their location;
• There are no metal strips;
• The warranty is given for only 2 years;
• The burnout process occurs randomly, and not over the entire surface.

grand line

This European well-developed siding company has about a dozen enterprises in Russia that produce high-quality and inexpensive products. In addition, the Grand Line manufacturer has about fifty service centers and cooperates with more than 7,000 sales agencies. The company manufactures vinyl siding, which includes premium, classic and luxury configurations with acrylic trims. The product range includes a special network of coatings for cold areas called Tundra. The manufacturer also produces metal panels, which are designed in the form of ship boards, eco-beam and steel plaster (this model is considered new).

This manufacturer is the best in creating siding precisely because of the wide range. Grand Line produces the most possible and impossible options for metal, vinyl and acrylic siding with a huge selection of colors.

• Availability of guarantees and certificates;
• Availability of free fans for calculating burnout;
• Huge range of colorings, ranging from golden oak to vanilla shade;
• Resistant to severe frosts.

• Sometimes there are different colors in one set;
• Requires frequent cleaning;
• The presence of burrs on the canvases;
• It is difficult to find an identical color on window slopes.

Nordside

This domestic siding manufacturer is located in the cultural capital of Russia - St. Petersburg, or rather its main office. The company's enterprises number more than 60 units throughout the Russian Federation and the CIS. To be precise, Nordside products are sold in 8 countries in 400 construction centers.

Despite the fact that this company is considered very young (2002), more than 400,000 homes have already been provided with its products.

As well as raw materials, specialized foreign equipment is used during the production of panels and all scrap materials.

A few years ago, the manufacturer introduced a new branch of sheathing - Karelia - into its assortment. These coatings are distinguished by a unique design, accompanied by a convex relief. This thread is worth checking out.

Similar to Tecos, the St. Petersburg manufacturer was included in the list of the best siding creators due to serious control over the manufacture and sale of materials. Nordside manufactures its coatings in accordance with European ISO 9001 standards.Compliance with GOST is monitored by the reputable Finnish company Aditum OY.

• A wide range of coatings with a variety of colors;
• Constant replenishment of new branches;
• All goods have the necessary certificates and comply with European standards.

• Weak resistance to severe cold;
• Production of exclusively vinyl panels;
• The mounting slots have too small jumpers.

Yu-layer

One of the best siding manufacturers was created in Belarus and promotes its products throughout the CIS. The company's product range includes a wide variety of lines, including Ship Timber, Block House, Stone House, Spruce, Timberblock and Timberblock Cedar. In addition, the company manufactures and supplies a large number of roof panels. This contributes to the beautiful merging of the facade of the building with its ceiling. Creative staff are constantly upgrading colors and designs.

Buyers claim that the Belarusian manufacturer produces good products at an average price, but experts point to the complex processing of panels with a cutting tool.

At the same time, experts call Yu-Plast one of the best siding manufacturers because of the large number of different types of panels needed to process the foundation. Based on the choice in the catalog, there are special Stone and Block ranges for the foundation, which are in the color of burnt stone, as well as in emerald and golden colors. These options feature a double lock that increases resistance to accidental impacts and gives a strong grip.

• The presence of European raw materials in the composition;
• Resistance to temperature extremes;
• Easy installation of panels due to low weight;
• Large selection of various colors.

• Exclusively vinyl products;
• The surface of the panels cracks when the self-tapping screws are clamped strongly;
• Difficult cutting tool.

Fineber

Fineber is considered the best Russian siding company. This manufacturer specializes in the manufacture of vinyl trim panels. Given the statistics from many sites, Fineber is considered the leader among sales, thus setting the bar for many European firms. The Russian manufacturer has several branches in its range. It includes the presence of the Block House and Standard series. Regarding the first series, there is an imitation of a ship's timber, and in the second - a log house. The colors are quite diverse and for a convenient choice they are divided into several categories. Each of them is distinguished by bright and defiant colors.

Experts note the cheapness of siding from the manufacturer Finebar. The fact is that despite the good quality, the cost of the panels is considered very cheap compared to many Russian competitors. In this case, we can say that Finebar is a bright representative of the budget option. On the part of experts, a remark is also noted about the choice of dark tones of the panels - they fade too quickly in the sun.

• Exposure to all European standards;
• Huge selection of colors;
• Flexible material for easy installation
• Cheap cost.

• To install the panels and connect them, special closures are required;
• It is difficult to fix the lock on long panels.

Overall assessment of manufacturers

This rating is based on the opinions of many buyers, as well as specialists who have repeatedly used the materials of the described manufacturers. During the preparation of the rating, all parameters, characteristics, as well as the advantages and disadvantages of manufacturers' products were taken into account. Perhaps this assessment in the future will help determine the successful choice of the necessary products.

Name	Position	Rating (from 1 to 10)	Cost (1pc)	Producing country
dock	1	9.1	150-550 rubles	Germany
Vox	2	8.8	150-340 rubles	Poland
Alta Profile	3	8.6	180-250 rubles	Russia
Mitten	4	8.2	200-400 rubles	Canada
Tecos	5	8.2	120-370 rubles	Russia
grand line	6	8	180-300 rubles	Great Britain
Nordside	7	8	100-450 rubles	Russia
U-Plast	8	7.8	130-300 rubles	Belarus
Fineber	9	7.7	160-450 rubles	Russia

Conclusion

After reviewing all the advantages and disadvantages of siding, it becomes clear that these coatings are the best and most reliable during operation. Varieties of interior decoration in these coatings are much greater than in other representatives of cladding materials. Absolutely every company described above produces the best siding materials that have almost the same advantages. Among the advantages you can find low cost, resistance to weather conditions and mechanical deformations, ease of installation, and, most importantly, a huge range of colors and designs.

There are also enough flaws in the panels. Basically, among them you can find an unpleasant smell after installation, too high cost, heavy weight, production of only vinyl coatings and a small assortment.

The article provides a list of the best manufacturers according to many experts, but you need to choose the right brand at your own discretion.